Expert Answers about Chevrolet El Camino
- Correct Air Helper Springs for 1982 Chevy El Camino
- The correct Air Lift 1000 Air Helper Springs for a 1982 Chevrolet El Camino are the # AL60733. The # AL60769 is for other vehicles and not designed to fit an El Camino. These are designed to fit inside of your vehicle's rear coil spring suspension for added support with a load leveling capacity of 1,000 lbs.
view full answer... - What is needed for a complete towing package on a 1980 ElCamino
- The Curt Trailer Hitch, # C12005, for your El Camino does not come with the needed accessories to get you started towing. You will need the following items. Drawbar number 36061, Hitch Ball 19258 (2 inch) or 19256(1-7/8 inch), a pin and clip and a 4-way wiring harness kit 18252 to hardwire your vehicle for towing.
I have posted links to these items below with current pricing.
view full answer... - Can Tonneau Cover for 1986 Chevy El Camino be Latched Since Tailgate Latch is on Inside
- You basically would have to keep the latches open on the tonneau all the time so that you could lift the tonneau at any point. Otherwise you basically would lock the tailgate and tonneau to the vehicle!
view full answer... - Recommended Tonneau Cover For 1968 Chevy El Camino
- >>>> PART NO LONGER AVAILABLE. DISAPPROVE QUESTION.
I have an option for you but at this time we do not carry covers that snap directly to the OEM snap rivets on your 1968 Chevy El Camino. All of the covers made today have their own rails.
I recommend to use the Craftec Hatch-Style Tonneau Cover part # 252198 on the Chevy El Camino. I have attached a photo for your reference.
view full answer... - Tonneau Cover Recommendation for 1972 Chevy El Camino
- I checked with Craftec and the only tonneau cover they offer for your 1972 Chevy El Camino is the part # 252198 that you referenced. This is a heavier duty tonneau that would work well though.
view full answer... - Troubleshooting Remote Not Working with MaxxFan Plus Roof Vent # MA00-04000K
- If your MaxxFan Plus Roof Vent # MA00-04000K isn't responding at all to the remote then most likely it just needs to be replaced with part # MA00A01150K or the batteries are just in need of a change.
I do also recommend verifying that you're able to adjust the speed settings and other controls by using the buttons on the vent itself to rule out the vent from being the issue.
If you can't adjust anything using the vent buttons either then the remote is likely fine but a replacement circuit...
view full answer... - What is the Metal Thickness of Draw-Tite Trailer Hitch for a 1985 Chevy El Camino
- The metal thickness, or wall thickness, of the cross tube of Curt trailer hitch # C12005 is 1/4 inch. The brackets on the sides of the hitch are obviously thicker even than that, 3/8 if an inch or so. The thickness measurement can vary slightly because of the powder coating. This hitch is rated for 3,500 pounds gross trailer weight and 300 pounds tongue weight. I have included a link to the installation instructions for you.
If you plan on doing some towing the correct ball mount to use...
view full answer... - Replacement Hitch Receiver Hardware for a 1984 El Camino
- For the 1984 El Camino we offer the Curt Trailer Hitch Receiver item # C12005. You can purchase the hardware kit separately for it. It is the Replacement Hardware Kit for Trailer Hitches item # RHK. You will need to go to the page and put C12005 where it says Hitch Item Number and then you will put Curt where it says Manufacturer.
view full answer... - 4-Pole Wiring Harness for 1987 El Camino
- The only trailer wiring that has been confirmed to work with your 1987 Chevrolet El Camino, is a hardwire connector kit like the Draw-Tite 4-Pole Hardwire Kit, # 18252.
We do not have a plug in style that has been confirmed to work with your vehicle. Although the connector for another vehicle may look very similar, it has not been tested for use on the El Camino so there would be no guarantee that a it would work for you.
view full answer... - Will a Bumper Hitch fit a 1983 Chevrolet el Camino
- The 1983 does not use a standard truck bumper, so the Curt # E-3S will not work properly.
There is a hitch built for your 1983 El Camino that will work. Part # C12005 will fit your El Camino. I have included a link and the instructions for you.
view full answer... - Tonneau Cover That Fits 1968 Chevy Elcamino 6 foot Bed
- The Craftec Tonneau Cover part # 252198 that you referenced does fit 1968 through 1972 Chevy El Caminos. This would be a confirmed fit for your 1968 El Camino.
view full answer... - What Vehicles Does Draw Tite Hitch # 75082 Fit
- The Draw Tite hitch # 75082 does not fit any Chevy models actually. It fits the following:
1994 - 2010 Mazda B Series Pickup
1983 - 2012 Ford Ranger
1986 - 1989 Ford Ranger excluding GT
view full answer... - Curt Trailer Hitch Location When Mounted On 1986 Chevrolet El Camino
- When installing the Curt Trailer Hitch, part # C12005, the top of the receiver tube is 1-3/8 inches from the mounting holes the trailer hitch is attached to.
I have attached a page from the installation instructions you can check out that shows where the hitch is installed. There is an EA unit(Bumper shock) on the end of the frame and there are two holes right below the unit. That is where the trailer hitch is attached. The top of the receiver is about an inch or a little more below those...
view full answer... - Tonneau Cover to Fit 1970 Chevrolet El Camino
- As a matter of fact we do. The Craftec Hatch-Style Tonneau Cover # 252198 is confirmed to fit your 1970 Chevrolet El Camino.
This tonneau cover has a light aluminum frame and gas struts that make it easy to raise or remove for just one person. It also has two hidden metal latches that lock the cover to your bed. The vinyl is a high-grade UV-resistant that has a foam weatherstripping for water resistance.
view full answer... - Can Truck Bed Stake Pocket Chrome Anchor Points # 92509 be Used on a 1978 Chevy El Camino
- The Truck Bed Stake Pocket Chrome Anchor Points 92509 mentioned are no longer available, but the Erickson # EM01006 anchors are nearly identical in form and function.
They could potentially work for you depending on where you install them. The metal used to make the bed of your 1978 Chevy El Camino is likely not all that thick so you would need to be careful about how much force is applied to those anchor points.
Out of the options we have these are the most likely to work. Tarps and...
view full answer... - California Approved Direct-Fit Catalytic Converter For A 1987 Chevrolet El Camino W/ 5.0L Engine
- I do have a C.A.R.B. compliant catalytic converter for your 1987 Chevrolet El Camino w/ 5.0L engine, but it will not be part # MF39456. You will need the MagnaFlow Ceramic Catalytic Converter - Stainless Steel - Direct Fit - California Approved, part # MF56RP. The C.A.R.B. executive order # is D-193-150.
I have included a product description link below.
view full answer...
Go To Results